![viewsonic drivers for skylake viewsonic drivers for skylake](https://c.dns-shop.ru/thumb/st4/fit/800/650/3045b31323b0f6567e9306fabd327b58/2f3d0e7a397f42822002c3b0761796cc648f01cd80c620277befbc1a4c149290.jpg)
Lead in high melting temperature type solders (i.e.Copper alloy containing up to 4% lead by weight.Lead as an alloying element in aluminum containing up to 0.4% lead by weight.Lead in glass of fluorescent tubes not exceeding 0.2% by weight.Long length (> 1,500 mm): maximum 13 mg per lamp.This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Substanceĥ00 mm and 1,500m): maximum 5 mg per lamp. The mark indicates the requirement NOT to dispose of the equipment as unsorted municipal waste, but use the return and collection systems according to local law. The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE). The following information is only for EU-member states: Consult the dealer or an experienced radio/TV technician for help.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Increase the separation between the equipment and receiver.Reorient or relocate the receiving antenna.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: However, there is no guarantee that interference will not occur in a particular installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with part 15 of FCC Rules. Confirmed corresponding applications shall refer to nameplate labels and relevant markings on the unit. This section addresses all connected requirements and statements regarding regulations. ↑ The test condition follows EEI standards.↑ Please use the power adapter from ViewSonic® or an authorized source only.↑ Do not set the graphics card in your computer to exceed these timing modes doing so may result in permanent damage to the display.Follow the key guide to return to the previous menu.NOTE: Certain menu option adjustments do not require the user to press the Middle key to confirm the selection. NOTE: If you want to display the laptop screen, you must unplug the Type C cable connected to the mobile phone. If a mobile phone is connected first to the TD1655, then a laptop is connected second, the mobile phone’s battery will be charged as one of the Type C ports is recognized as being connected to a power adapter. NOTE: If you want to display the mobile phone’s screen, you must unplug the Type C cable connected to the laptop. If a laptop is connected first to the TD1655, then a mobile phone is connected second, the mobile phone’s battery will not be charged as neither Type C port recognizes the connection as being connected to a power adapter. Only when one of the Type C ports is recognized as a power adapter can the other one deliver two-way power.When a Type C port recognizes an external device as a power adapter, it will only distribute the power.The first connected device will be the main input signal.NOTE: Due to the limited power output of the mobile phone, do not adjust the brightness level higher as this may cause the display to flash or shut down. When using a mobile phone to power the monitor, the default brightness level will be 15.If the power source is a mobile phone, the default brightness value will be 15.
![viewsonic drivers for skylake viewsonic drivers for skylake](https://www.lifewire.com/thmb/akKvFQvlDLwoeMRv2V7CdmcGv3Q=/768x0/filters:no_upscale():max_bytes(150000):strip_icc()/viewsonic-logo-56a6fabb5f9b58b7d0e5d119.png)
If the power source is an adapter or notebook, the default brightness value will be 100.This product will detect if the power supply device is an adapter, laptop or mobile phone.